SPECIAL AEROSOL SOLVENT DEGREASER FOR CONTACTS
DECONTAMINATION AND DEPOLLUTION SOLVENT
FOR ELECTRICAL AND ELECTRONIC COMPONENTS
WITHOUT EFFECT ON THERMOSET PLASTICS AND IMPREGNATING RESINS
IMMEDIATE EVAPORATION, INSTANTANEOUS DRYING, FOR DRY CLEANING
DIELECTRIC STRENGTH (IEC156 43000 VOLTS)
DESCRIPTION
Dry cleaning solution aerosol, dielectric strength, Neutralene® HV1, Ibiotec, aerosol cleaning solution for contacts, quick-drying cleaning solution, cleaning aerosol for electronic and electrical equipment.
NEUTRALENE® HV1 quick-drying cleaning solution is highly recommended for degreasing, cleaning and decontamination of all metals, composites, glass and ceramics, as well as most plastics and elastomers. It eliminates all organic and inorganic contamination.
This solvent is used in electronics, precision engineering, aerospace, optics and on all electrical equipment. It is particularly recommended for restoring electrical characteristics whilst avoiding sparking and leakage currents. NEUTRALENE® HV1 cleaning solution aerosol can be used to prepare surfaces before insulation.
It can also be used to prepare surfaces before gluing, painting, metal-plating, insulation or tropicalisation.
FIELDS OF USE
Maintenance of all electrical equipment, cabinets, photocells, cut-off switches, circuit breakers, contact switches, rheostats, rectifiers and motors. It does not affect insulating varnishes.
Decontamination of connections, busbars, fuse holders, fins on low voltage transformers.
Cleaning of open-cell or pre-block insulators, transformer penetrations, Buchholz relays, pressure gauges and valves.
Cleaning and silicone removal from EHV distribution stations and connectors before manual or infra-red camera inspection.
Cleaning of all direct contacts, potentiometers, keyboards, sliders, rotary contacts.
Servicing of low voltage equipment: telephony, telecommunications, air and sea navigation equipment.
Cleaning of microswitches, semiconductor pads, electronic tracks.
Cleaning of SMC circuits.
PHYSICO-CHEMICAL PROPERTIES
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
Appearance |
Visual |
Fluid |
- |
|
Colour* |
Visual |
Colourless |
- |
|
Scent |
Olfactory |
Slight |
- |
|
Density at 25°C |
NF EN ISO 12185 |
1018 |
kg/m3 |
|
Refraction index |
ISO 5661 |
1.4120 |
- |
|
Freezing point |
ISO 3016 |
-30 |
°C |
|
Water solubility |
- |
Insoluble |
% |
|
Kinematic viscosity at 40°C |
NF EN 3104 |
1.2 |
mm²/s |
|
Acid index |
EN 14104 |
<0.1 |
mg(KOH)/g |
|
Iodine index |
NF EN 14111 |
n.m |
gI2/100g |
|
Water content |
NF ISO 6296 |
0.0 |
% |
|
Residue after evaporation |
NF T 30-084 |
0.0 |
% |
|
Steam pressure at 20°C |
NF EN 13016-1 |
>0.1 |
hPa |
|
PERFORMANCE PROPERTIES |
|||
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
KB index |
ASTM D 1133 |
75 |
- |
|
Evaporation speed |
- |
6 |
dry |
|
Boiling point |
NF EN 14,667 ASTM D 5399 |
55 |
°C |
|
Surface tension at 20°C |
ISO 6295 |
21.2 |
dyne/cm |
|
Breakdown voltage |
NF EN 60156/IEC 156 |
43,000 |
Volts |
|
Copper blade corrosion 100 h at 40°C |
ISO 2160 |
1a |
Measured value |
|
FIRE SAFETY PROPERTIES |
|||
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
Flashpoint (closed tank) |
ISO 2719 |
Without |
°C |
|
Self-combustion point |
ASTM E 659 |
Without |
°C |
|
TOXICOLOGICAL PROPERTIES |
|||
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
Anisidine index |
NF ISO 6885 |
0 |
- |
|
Peroxide index |
NF ISO 3960 |
0 |
meq(O2)/kg |
|
TOTOX (anisidine index+2x peroxide index) |
- |
0 |
- |
|
CMR, irritant and corrosive substance content |
CLP Regulation |
0 |
% |
|
Residual methanol content from transesterification |
GC-MS |
0 |
% |
|
Emissions of hazardous compounds, CMR, irritants, corrosive at 160°C |
GC-MS |
0 |
% |
|
ENVIRONMENTAL PROPERTIES |
|||
|
PROPERTIES |
STANDARDS |
VALUES |
UNITS |
|
Steam pressure at 20°C |
- |
>0.1 |
hPa |
|
VOC content (Volatile Organic Compounds) |
- |
100 |
% |
|
Sulphur content |
GC MS |
0 |
% |
|
Benzene content |
ASTM D6229 |
0 |
% |
|
Total halogen content |
GC MS |
0 |
% |
|
Chlorinated solvent content |
- |
0 |
% |
|
Aromatic solvent content |
- |
0 |
% |
|
Environmentally-hazardous substance content |
CLP Regulation |
0 |
% |
|
GWP |
- |
<150 |
% |
|
Content of compounds with ODP |
- |
0 |
% |
|
Carbon assessment, life cycles analysis. |
ISO 14040 |
nm |
Kg carbon equivalent |
*nm: not measured or cannot be measured
INSTRUCTIONS FOR USE
Shake the aerosol from bottom to top for a few seconds. Spray 20 cm from the surfaces to be treated, according to its size.
Aerosol usable in all positions.
PRESENTATION
|
|
Aerosol 650 ml
|
Looking for another product?
|
Discover our entire range by clicking on the photo |
Manufacturing, lubrification, cleansing, protection,
IBiotec® Tec Industries® Service
offers a wide range of products reserved for industrial area
If you wish for :
a free sample
a technical advice
a product data sheet
a safety data sheet
IBiotec® Tec Industries®Service
manufacturer of technical chemical products.
Welcome to our website.
IBiotec® Tec Industries®Service is on : 